Click the Exhibit button and view a network diagram and a switch configuration.

In RRPP ring # 3, which type of port is interface G 1/0/2 of Switch 2?

• A. Common
• B. Secondary
• C. Assistant Edge
• D. Transit
• E. Primary
• F. Edge

During the past several weeks, users have begun complaining about the poor quality of VoIP phone calls. While VoIP has been in use for several months, recently there has been network congestion and performance has been adversely affected. You have implemented a QoS Policy on the router where the congestion is occurring however, the voice quality does not seem to improve.

Based on the information above, what is causing the issue?

• A. improper classification of VoIP traffic
• B. insufficient interface bandwidth
• C. improper application of the policy
• D. improper marking of VoIP traffic

Click the Exhibit button and view the three exhibits.



Network 16.2.0.0 /16 is advertised by Router 1 and Router 2 into BGP. All traffic from AS-65002 destined to 16.2.0.0 /16 enters AS 65001 via the Serial 3 interface of Router 1. The administrator prefers that this traffic enter AS 65001 via interface Serial 4 of Router 2. Which configuration change is most likely to achieve the desired results?

• A. Router-1#Router-1# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 6000 route-policy PolicyB permit node 100 Router-2# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 7000 route-policy PolicyB permit node 100
• B. Router-1# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 3000 route-policy PolicyA permit node 100 Router-2# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 2000 route-policy PolicyA permit node 100
• C. Router-1# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 3000 route-policy PolicyB permit node 100 Router-2# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 2000 route-policy PolicyB permit node 100
• D. Router-1# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 6000 route-policy PolicyA permit node 100 Router-2# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 7000 route-policy PolicyA permit node 100

DRAG DROP
Click the Task button. A customer wants to replace the two Cisco switches at the distribution layer (Cisco_D1 and Cisco_D2) with two HP A-Series switches. Currently the Cisco distribution layer switches implement Hot Standby Router Protocol (HSRP) and act as the default gateways for all endpoints in the LAN. Cisco_D1 and Cisco_D2 each act as the active router for half of the LAN VLANs. The distribution switches connect to a WAN router, whichCisco_D1 and Cisco_D2 each act as the active router for half of the LAN? VLANs. The distribution switches connect to a WAN router, which provides the Internet connection and have a default route to that router for all non-local traffic. You decide to remove the Cisco switches one at a time and replace them, one at a time, with the HP A-Series switches. For the first step, you will remove the Cisco_D1. You want to incur as little downtime as possible. Place the configuration tasks for removing Cisco_D1 in the correct order.

Which statement is true about BGP Route Refresh? (Select two.)

• A. With Route Refresh, a BGP Hard Reset is used to generate inbound updates from a neighbor or to generate outbound updates to a neighbor.
• B. With Route Refresh, a BGP router stores all BGP prefixes sent by a BGP neighbor.
• C. Route Refresh is a feature for supported CPU functions with BGP routers that manage high number of IP Prefixes.
• D. Route Refresh is advertised as a BGP capability to BGP neighbors during BGP session establishment.
• E. BGP Route Refresh eliminates the need for a Hard Reset of the BGP connection with a BGP neighbor when route policies are changed.